Adjustable support clamp 30 MM
Produced in galvanised steel 2.0 mm thick, this clamp is for connections between the ridge/corner and the roofing structure. The structure formed by the clamp + batten assembly will be responsible for the reaction of the roof ridges and corners to gravity and to the wind. Thanks to the varied borings and the large length of the support pincers (210 mm), the part is able to cope with the height of any construction solution. Its 30x30 mm base has been designed to thoroughly and effectively attach a support batten of the same section. It has holes on each side of the base for clamping the batten. It also has a 45 mm thread variation for final level adjustments.
Material
Galvanised steel
Colour
4030446 - steel
Application
The clamp should be screwed directly into the roof covering structure. Thanks to the varied borings and the appropriate screw, depending on the support, it is always possible to fix the clamp in a secure and effective manner. The 30x30 mm batten section, ideally of wood, is laid, fixed on both sides.
Special Clamp Characteristics
Width: 30 mm
Length: 210 mm
Thickness: 2mm
Unit Weight: 0,169 kg
Yield: 2 un/m
Length: 210 mm
Thickness: 2mm
Unit Weight: 0,169 kg
Yield: 2 un/m
Universal support clamp
Produced in galvanised steel 2.0 mm thick, this clamp is for connections between the ridge/corner and the roofing structure. The structure formed by the clamp + batten assembly will be responsible for the reaction of the roof ridges and corners to gravity and to the wind. Thanks to the varied borings and the large length of the support pincers (210 mm), the part is able to cope with the height of any construction solution.
Material
Galvanised steel
Colour
4064881 - steel
Application
The clamp should be screwed directly into the roof covering structure. Thanks to the varied borings and the appropriate screw, depending on the support, it is always possible to fix the clamp in a secure and effective manner. The 30x30 mm batten section, ideally of wood, is laid, fixed on both sides.
Special Clamp Characteristics
Width: 50 mm
Length: 210 mm
Thickness: 2mm
Unit Wieght: 0,175 kg
Yield: 2 un/m
Length: 210 mm
Thickness: 2mm
Unit Wieght: 0,175 kg
Yield: 2 un/m
SPECIAL TILE CLAMP
Produced in stainless steel, 1.5 mm thick and with a mechanically effective clamping principle. This piece was designed to meet the most peculiar needs of mechanical fixing of roofs. Usually used when it is not possible to fasten ceramic parts directly with screws. When the supports below the holes of the parts are not suitable for fixing, this clamp enables the parts to be fixed at a support point some distance from the fixation application point.
Material
Stainless steel
Colour
4031001 - steel
Application
The clamp should be tightened on the ceramic part through use of a mallet. Later the piece is applied in the place and the clamp goes to the point of fixation resorting to its stainless steel cord.
Application examples:
Fixation of spout and eave over tiles to malleable substrates (bituminous sub-tile substrates) or to stone cornices (to avoid drilling of the cornice).
Fixing of Lusa half-tiles and other hedge parts. | Fixing cut parts in the roof ridges, corners and draining valleys.
Special Clamp Characteristics
Width: 180 mm
Length: 410 mm
Height: 200 mm
Unit Weight: 0,010 kg
Thickness: 1,00 - 1,50 mm
Length: 410 mm
Height: 200 mm
Unit Weight: 0,010 kg
Thickness: 1,00 - 1,50 mm
FIXATION CLAMP FOR LUSA RIDGE
Resistant to atmospheric influences, the fixation clamp for the Lusa ridge has high resistance to form and function with a long life. The fixing clamp of the Lusa ridge is applicable in roof ridges and corners. Designed specifically for UMBELINO MONTEIRO ridge tilings. The rods of the fastening clamp of the Lusa ridge are easily foldable, allowing an easy adaptation to the "nose of the ridge tile". In addition, the holes allow quick and effective fixing on the batten.
Material
Galvanised steel
Colour
4031002 - red
Application
The clamp should be screwed onto the batten ridge, perforating the membrane in the upper part. It is placed in the overlapping measure over the previous ridge. Then the next ridge tile is laid. Through flexible “shafts” that bend, the clamp directly attaches to the ridge tile in the higher area and on the protrusion of the ceramic part usually known as the “nose of the ridge tile”.
Characteristics of the Fixation Clamp for the Lusa Ridge
Width 1: 12 mm
Width 2: 80mm
Length: 145 mm
Unit Weight: 0,016 kg
Thickness: 2 mm
Width 2: 80mm
Length: 145 mm
Unit Weight: 0,016 kg
Thickness: 2 mm
FIXATION CLAMP FOR THE MARSEILLE RIDGE
Resistant to atmospheric influences, the fixation clamp for the Marseille ridge has high resistance to form and function with a long life. The fixation clamp of the Marseilles roofing is applicable on roof ridges and corners. The fixation rods of the Marseille ridge hold the Marseille ridge laterally.
Material
Galvanised steel
Colour
4030445 - steel
Application
The clamp should be screwed onto the batten ridge, perforating the membrane in the upper part. It is placed in the overlapping measure below the ridge tile that we will lay. Then the next ridge tile is laid. Through the flexible “shafts” which bend on each side, the clamp snaps directly onto the ridge tile. Mastique may be used at this point for better attachment to the part.
Characteristics of the Fixation Clamp for the Marseille Ridge
Width: 25 mm
Length: 200 mm
Unit Weight: 0,071 kg
Thickness: 2 mm
Length: 200 mm
Unit Weight: 0,071 kg
Thickness: 2 mm
FIXATION CLAMP FOR THE UNIVERSAL RIDGE
Resistant to atmospheric influences, the fixation clamp for the universal ridge has high resistance to form and function with a long life. The fixation clamp of the universal ridge is used in roof ridge and corner areas for all the UMBELINO MONTEIRO roof tile ranges.
Material
Lacquered Aluminium
Colour
4064882 - red clay
Application
The clamp should be screwed onto the batten ridge, perforating the membrane in the upper part. It is placed in the overlapping measure below the ridge tile that we will lay. Then the next ridge tile is laid. Through the “shafts", the clamp snaps directly onto the ridge tile. Mastique may be used at this point for better attachment to the part.
Characteristics of the Fixation Clamp For the Universal Ridge
Width: 18 mm
Length: 110 mm
Unit Weight: 0,015 kg
Thickness: 2 mm
Length: 110 mm
Unit Weight: 0,015 kg
Thickness: 2 mm
STEEL CLAMP AISI 304 FOR TRADITIONAL CANUDO CLAY TILE 3 MM
Produced in stainless steel with 3.0 mm thickness, this clamp aims to correctly fix all the sloping tiles, which are UM Canudo clay tiles. Its shape allows an ideal overlap of 10 cm between tiles. It guarantees the reaction to the gravitational and wind sliding of the straw canopies -traditional Canudo clay tiles- eliminating any other bonding element (masses, foams, etc.). It guarantees greater entrance and circulation of air in the roof. Due to its characteristics it is resistant to all the elements, ensuring effective fixings throughout the useful life of the roof, without rusting or corroding.
Material
Steel AISI 304
Colour
4030461 - inox
Application
The clamp should be fastened to the top part of the traditional Canudo clay tile and placed on it, in order to help with overlapping/fixing the next tile.
Note: if the slopes have pitches of more than 50% and lengths are greater than 4.0 m,the mechanical fixing should be made with an intermediate screw for a drilled over tile. For more information/clarifications consult theUM Canudo Installation Guide or contact UMBELINO MONTEIRO’s Technical Department.
Aisi 304 Steel Clamp characteristics for traditional canudo clay tile 3 mm and Packaging
Width: 13 mm
Length: 95 mm
Unit Weight: 0.009 Kg
Thickness: 3 mm
Package: 500 units
Package Width: 15.5 cm
Package Length: 31 cm
Package Height: 13 cm
Length: 95 mm
Unit Weight: 0.009 Kg
Thickness: 3 mm
Package: 500 units
Package Width: 15.5 cm
Package Length: 31 cm
Package Height: 13 cm
STEEL CLAMP AISI 304 FOR TRADITIONAL CANUDO CLAY TILE 2.4 MM
Produced in stainless steel 2.4 mm thick.
Material
Steel AISI 304
Colour
4030461 - inox
Application
The clamp should be fastened to the top part of the traditional Canudo clay tile and placed on it, in order to help with overlapping/fixing the next tile.
Notes: 1. If the slopes have pitches of more than 50% and lengths are greater than 4.0 m, the mechanical fixing should be made with an intermediate screw for a drilled over tile. For more information / clarifications consult the UM Canudo Application Guide or contact the UMBELINO MONTEIRO Technical Department. | 2. The use of this clamp should take into account not only the functional requirements of the roofs, but also their geometry and especially the local meteorological actions, as they may influence the rapid deformation / degradation of the part. | 3. The option to use this thickness of clamp is entirely the responsibility of the designer/construction manager.
Notes: 1. If the slopes have pitches of more than 50% and lengths are greater than 4.0 m, the mechanical fixing should be made with an intermediate screw for a drilled over tile. For more information / clarifications consult the UM Canudo Application Guide or contact the UMBELINO MONTEIRO Technical Department. | 2. The use of this clamp should take into account not only the functional requirements of the roofs, but also their geometry and especially the local meteorological actions, as they may influence the rapid deformation / degradation of the part. | 3. The option to use this thickness of clamp is entirely the responsibility of the designer/construction manager.
Aisi 304 Steel Clamp characteristics for traditional canudo clay tile 3 mm and Packaging
Width: 13 mm
Length: 95 mm
Unit Weight: 0.006 Kg
Thickness: 2.4 mm
Bag: 250 units
Package: 750 units
Package Width: 15.5 cm
Package Length: 31 cm
Package Height: 13 cm
Length: 95 mm
Unit Weight: 0.006 Kg
Thickness: 2.4 mm
Bag: 250 units
Package: 750 units
Package Width: 15.5 cm
Package Length: 31 cm
Package Height: 13 cm
EAVE FIXING CLAMP
The fixation clamp for the eave works along with the screw to ensure the correct fixing of the roof tiles on the eave. Whether it is the eaves composed of the tile itself or by special pieces (spouts and eyelash covers), the clamp allows you to secure the pieces effectively ensuring freedom of movement in any direction. Effective to ensure that eave parts / eaves are not "plucked" over time and by the action of wind.
Produced in lacquered zinc, the part bends easily according to the height of the ceramic part.
Produced in lacquered zinc, the part bends easily according to the height of the ceramic part.
Material
Zinc
Colour
4055255 - zinc
Application
Laying diagram: The fixation part is placed on one side and approximately halfway between the spout/eave tile, depending on how far the part overhangs. It is usually fixed at the same point of the PVC protection mesh using the appropriate screw.
Notes: Due to its versatile design, this part is also used in situations where there is a need for additional fixing.
Aisi 304 Steel Clamp characteristics for traditional canudo clay tile 3 mm
Width: 15 mm
Length: 100 mm
Unit Weight: 0.010 Kg
Thickness: 3 mm
Yield: 5 un / m
Length: 100 mm
Unit Weight: 0.010 Kg
Thickness: 3 mm
Yield: 5 un / m
Our Brands
Here you can get to know our brands for your project. Let yourself be inspired!
Where to buy
Find your nearest point of sale.